Bathroom Remodeling in Austin, TX

How Much Does a Bathroom Remodel Cost in Austin? (2026)

A bathroom remodel in Austin costs $18,000 to $40,000 for a typical mid-range full bath in 2026, with the wider market running from about $6,000 for a simple powder-room update to $150,000+ for a luxury spa-style primary suite. A powder or half bath (toilet, vanity, and finishes, no shower or tub) runs $6,000 to $18,000. A guest or hall full bath with a tub-shower combo, tile, and a new vanity typically lands at $18,000 to $40,000. A primary or ensuite bath with a tiled walk-in shower, a double vanity, and often a freestanding soaking tub runs $35,000 to $75,000, and a luxury spa remodel with curbless wet areas, natural stone, heated floors, and custom cabinetry starts near $75,000 and climbs past $150,000. Bathrooms run more per square foot than almost any room in the house, commonly $250 to $650, because a small space packs waterproofing, tile, plumbing, and electrical into every corner. Where your project lands depends far more on shower and tub scope, the tile and stone you pick, and whether plumbing moves than on the room's size. HN Construction & Remodeling prices each of these as a fixed line-item figure in your written bathroom remodel estimate before work begins, so the number you sign is the number you pay.

A full bathroom remodel is really a stack of smaller budgets, and here the tile and waterproofing line carries the room the way cabinets carry a kitchen. The table below breaks a typical 2026 greater-Austin full bath into its major line items with realistic installed ranges. A powder-bath refresh shifts weight toward finishes and skips the shower work; a primary or spa remodel pushes tile, glass, and labor higher. In HN Construction & Remodeling's fixed line-item estimates, each trade's install labor is built into that trade's line, so these figures show where the money goes rather than a materials-only price.

A handful of choices move a bathroom remodel budget far more than square footage does. These are the cost drivers HN Construction & Remodeling walks through with you before writing a fixed line-item estimate:

• Tub-to-shower conversion - swapping an old tub for a walk-in shower adds roughly $8,000-$20,000 on its own, because it means new waterproofing, a rebuilt or low-threshold pan, a new valve, and glass. Adding a tub where none exists runs high for the same reasons, plus the extra drain and filler rough-in.
• Moving plumbing - relocating the toilet flange, shower drain, or vanity supply lines means opening the floor or slab and rerouting pipe, often $1,500-$6,000+ plus a permit. Keeping fixtures where they already are is the single biggest way to hold a bathroom budget down.
• Tile and stone choice - basic ceramic subway runs about $12-$18 per sq ft installed, while large-format porcelain, handmade zellige, marble, and mosaic accents can double or triple that in both material and labor. A floor-to-ceiling tiled shower uses far more tile than a partial surround.
• Curbless / zero-threshold shower - a flush, curbless entry (ideal for aging-in-place and a clean modern look) requires recessing the shower pan into the framing or slab and setting a linear drain, adding roughly $2,000-$6,000 over a standard curbed shower.
• Double vanity - a second sink, faucet, and wider cabinet with a longer stone top adds about $2,000-$5,000+ over a single vanity, plus the extra plumbing rough-in for the second drain and supply lines.
• Older-home surprises - central-Austin homes from the 1920s to 1960s often hide galvanized or cast-iron drain pipe, no real waterproofing under decades-old tile, rotted subfloor or wall studs behind the tub, and undersized wiring. These surface at demolition and have to be corrected before rebuilding, which is why a 10-20% contingency is wise on an older bath.

Walk-In Showers, Tub-to-Shower Conversions & Aging-in-Place

The bathroom remodels HN Construction & Remodeling builds most often in Austin are tub-to-shower conversions, walk-in and curbless showers, double-vanity primary baths, and aging-in-place updates, with most single-bathroom projects running $8,000 to $35,000 depending on size, tile, and fixtures. Here is what each project involves and what it typically costs in the 2026 greater-Austin market.

• Walk-in and curbless (zero-threshold) showers - an open shower with no curb to step over, built on a properly sloped, fully waterproofed pan with a linear (trench) drain. The most-requested primary-bath upgrade in Austin, typically $9,000 to $22,000 depending on size, tile, and glass.
• Tub-to-shower conversions - removing a rarely used builder-grade drop-in or cramped hall tub and rebuilding the space as a full tiled shower with a bench, niche, and frameless glass. One of the highest-value bathroom remodels in the Austin market, usually $8,000 to $18,000.
• Freestanding and soaking tubs - a sculptural freestanding soaker as a centerpiece or a deck-mounted tub in the primary bath. The tub itself commonly runs $1,500 to $6,000, plus roughly $600 to $1,800 for a floor-mounted filler and the plumbing rough-in.
• Double vanities - two sinks with dedicated storage and counter space, the standard ask for primary-bath remodels, typically $3,500 to $12,000 installed depending on semi-custom vs. custom cabinetry and countertop material.
• Wet rooms - a single, fully waterproofed zone that combines a soaking tub and a walk-in shower behind one glass panel, a space-smart layout for the narrower floor plans common in Central Austin homes.
• Aging-in-place and ADA-friendly baths - curbless zero-threshold entries, blocking-backed grab bars, a built-in bench, a handheld sprayer on a slide bar, comfort-height (chair-height) toilets, slip-resistant tile, and a wider 36-inch-plus doorway for walker or wheelchair access. In steady demand with Austin homeowners planning to stay in place and throughout Georgetown's Sun City.
• Powder rooms and guest-bath refreshes - a compact half bath or hall bath updated with a new vanity, toilet, tile, lighting, and fixtures, usually $5,000 to $15,000 and a fast way to modernize without touching the primary suite.

Tile, Vanities, Waterproofing & Finishes for Austin Bathrooms

For an Austin bathroom, the finish that matters most is the waterproofing you never see. Austin's warm, humid climate combined with daily hot showers makes water management the difference between a shower that lasts 20-plus years and one that grows mold or rots the subfloor within five. HN Construction & Remodeling waterproofs every wet area with a modern bonded system rather than relying on tile and grout, which are not waterproof on their own. In practice that means a Schluter-Kerdi sheet membrane or a liquid-applied membrane (such as RedGard) over the backer board, a pre-sloped and fully bonded shower pan, and sealed corners, seams, and pipe penetrations. For curbless, zero-threshold showers we recess and slope the subfloor and use a linear (trench) drain so water runs to the drain instead of out onto the bathroom floor. Getting the pan slope, membrane, and drain right is the single most important thing a bathroom remodeler in Austin does, and it is exactly where cheap or rushed work fails.

Above the waterproofing, tile is the defining finish. Porcelain is the workhorse for Austin bathrooms because it is dense, low-porosity, and nearly waterproof, which makes it ideal for shower floors and walls; ceramic is a budget-friendly choice for dry walls; and natural stone (marble, travertine, limestone, slate) delivers a high-end look but is porous, etches with acidic products, and needs periodic sealing, something worth weighing against Austin's hard water. Small-format mosaic on a shower floor gives both the slope and the slip resistance you want, while large-format porcelain on walls means fewer grout lines to maintain. For vanities, semi-custom cabinets fit most budgets while fully custom suits older, out-of-square Central Austin homes and floating (wall-mounted) designs; either way HN Construction favors plywood or moisture-resistant boxes over MDF near water, and quartz is the most popular vanity countertop here because it is non-porous and never needs sealing, with granite and marble also common. Two details matter more in Austin than almost anywhere: ventilation and fixture finish. An exhaust fan should be sized to the room (roughly 1 CFM per square foot for standard 8-foot ceilings, and never smaller than 50 CFM) and vented to the outside rather than into the attic, ideally on a humidity-sensing or timer switch, because under-venting is the number-one cause of bathroom mold in our climate. And because Austin runs on hard, high-mineral water, brushed nickel, matte black, and champagne-bronze fixtures hide mineral spotting far better than polished chrome, and a durable PVD finish holds up longer.

• Porcelain tile - dense, low-porosity, and the most durable choice for Austin shower floors, walls, and bathroom floors; large-format panels reduce grout lines and upkeep.
• Ceramic tile - a budget-friendly option best suited to dry walls and accent areas rather than heavy wet-zone use.
• Natural stone (marble, travertine, limestone, slate) - a premium look that is porous, etches with acidic cleaners, and needs periodic sealing, a real consideration with Austin's hard water.
• Waterproofing systems - a bonded Schluter-Kerdi or liquid-applied membrane over backer board, a pre-sloped and fully sealed shower pan, and a linear drain for curbless showers; tile and grout alone are not waterproof.
• Semi-custom vs. custom vanities - semi-custom for most budgets, custom for out-of-square older homes, tall runs, and floating designs; plywood or moisture-resistant boxes over MDF anywhere near water.
• Countertops - quartz for the lowest upkeep (non-porous, no sealing needed), with granite and marble also popular for vanity tops.
• Exhaust ventilation - a fan sized to the room (about 1 CFM per sq ft, minimum 50 CFM), vented to the exterior on a humidity or timer switch, the best defense against Austin bathroom mold and moisture damage.
• Hard-water-friendly fixtures - brushed nickel, matte black, and champagne-bronze finishes hide mineral spotting better than polished chrome, and a whole-home softener further protects fixtures and shower glass.

Austin Neighborhoods & Areas We Serve

HN Construction & Remodeling is based in Austin and remodels bathrooms across the city and the greater Austin metro, from Tarrytown and Hyde Park to Round Rock, Cedar Park, and Bee Cave. Because a bathroom holds a home's oldest and most hidden plumbing, and because Austin's housing stock ranges from 1920s cottages to 2010s master-planned homes, the right approach changes by neighborhood, from rerouting cast-iron drains in a central-Austin bungalow to building a curbless spa shower in a West Lake Hills primary suite. Several of these communities also run their own permitting departments separate from the City of Austin. Areas we serve regularly include:

• Tarrytown and central Austin - 1930s to 50s homes with small original hall baths, aging cast-iron or galvanized drain lines, and little or no exhaust ventilation; remodels here often mean rebuilding the wet area from the studs and replacing old plumbing.
• West Lake Hills and Lakeway - high-end primary suites with curbless spa showers, freestanding soaking tubs, and double vanities; both cities run their own building departments, so hillside-lot permitting runs stricter and longer than in the City of Austin.
• Hyde Park - 1920s cottages, many inside the local historic district, that frequently have just one small bathroom; interior updates modernize plumbing, waterproofing, and ventilation without altering the protected exterior.
• Zilker and Barton Hills - compact bungalows near Barton Springs where the goal is often converting a cramped tub to a walk-in shower or fitting a second bath into a tight footprint.
• Mueller - newer, energy-efficient homes with sound baths already in place; projects here lean toward tile, vanity, and curbless-shower upgrades under the Mueller POA design guidelines.
• Circle C Ranch - 1990s to 2000s southwest Austin homes with builder-grade garden tubs and cultured-marble surrounds that are prime candidates for tub-to-shower conversions and double vanities.
• Round Rock - Williamson County family homes permitted through the City of Round Rock, where guest-bath and primary-bath updates are the common request.
• Cedar Park - suburban homes across Williamson and Travis counties, permitted through the City of Cedar Park, where oversized builder garden tubs are often converted to large walk-in showers.
• Leander - one of the metro's fastest-growing cities, permitted through the City of Leander, with newer homes getting their first bathroom upgrades.
• Pflugerville - value-focused remodels that replace one-piece fiberglass tub-shower units with fully tiled, properly waterproofed showers.
• Georgetown - a mix of historic downtown homes under city overlays and Sun City retirement builds, permitted through the City of Georgetown, where aging-in-place features like curbless entries and grab bars are especially in demand.
• Bee Cave - upscale Lake Travis-area primary baths permitted through the City of Bee Cave, often paired with natural stone, freestanding tubs, and custom cabinetry.